November 19, 2026
Does Photonic Layer Security Add Latency to My Fiber Link? What I Learned From the Numbers
A check of fiber delay, security-layer latency, and reach for photonic layer security, including where the published figures stop.

By CyberWatch
5 min read
- Fiber sets link delay at about 5 microseconds per kilometer, according to CommScope, so a 100 km span carries about 500 microseconds one way with or without a security layer.
- Photonic layer security adds no additional latency to a fiber link, because it processes the signal in the optical domain with no packet overhead.
- A photonic layer security link runs up to 100 km per unamplified span and stays compatible with EDFA and Raman amplifiers on longer routes.
- A 2025 arXiv survey puts fiber quantum key distribution at roughly 50 to 100 km without trusted relay nodes.
- CyberRidge's Carmel, Ciena's WaveLogic Encryption, and Adva's ConnectGuard all work at Layer 1 of an optical link, and they differ mainly in how each publishes its latency, reach, and line-rate figures.
I expected a trade-off, because anything that protects a link usually costs delay or distance. Photonic layer security turned out to be the exception on delay, since the fiber alone sets link delay at about 5 microseconds per kilometer and the security layer adds nothing to it. On reach, a single span runs up to 100 km without amplification, with EDFA and Raman amplifiers on longer routes.
Where the delay on a fiber link comes from
Fiber sets link delay at about 5 microseconds per kilometer, and that figure is the same with or without a security layer. CommScope traces it to light travelling about 1.5 times slower in glass than in a vacuum. A 100 km span therefore carries about 500 microseconds of one-way delay, and an 80 km span about 400 microseconds. Any claim of added delay has to be measured against those totals.
Every device in the path adds delay on top of the fiber, and packet-layer encryption is one of those hops. A 2018 multilayer network study names complexity and added latency as the main drawbacks of IPsec. Photonic layer security is not one of those hops, because it works on the optical signal and never handles packets.
Layer 1 delay measured in nanoseconds
Layer 1 hardware adds nanoseconds where packet-layer tools add microseconds or more. In a 2014 GCN column, Uli Schlegel of ADVA Optical Networking wrote that 100 Gb/s networking with Layer 1 encryption adds less than 150 nanoseconds of latency. At 5 nanoseconds per meter of fiber, 150 nanoseconds equals about 30 meters of cable, or 0.03 percent of the fiber delay on a 100 km span. That ratio is what convinced me delay is not the deciding factor at these distances.
Photonic layer security adds no additional latency because its processing happens in the optical domain with no packet overhead. One implementation spreads the signal across 1 to 2 terahertz of the C-band, with optical keys that change continuously. A buyer who needs a measured value for a specific path can request one in a proof of concept.
Curious what a fiber tap records under photonic layer security and under optical encryption? This video walks through both side by side.
How far a single span goes before it needs an amplifier
A photonic layer security link runs up to 100 km per unamplified span, and the published results sit in that band. A 2025 Journal of Lightwave Technology paper established a 100 Gbps DP-QPSK signal over 80 km of standard single-mode fiber, and the EU's CORDIS project database describes links of 80 to 100 km. The two sources agree on one band for a single span, so 80 to 100 km is the planning unit.
Longer routes require amplifiers, and photonic layer security is compatible with EDFA and Raman amplification with no maximum amplified distance specified. Quantum key distribution cannot use them. A 2025 arXiv survey of enterprise quantum-safe readiness puts fiber QKD at roughly 50 to 100 km without a trusted relay node, because amplifiers would disturb the photon states.
What the published figures leave open
Fiber delay is physics, and a longer route carries proportionally more of it. The published sources give no measured latency for any specific path, so a proof of concept supplies that number. Reach beyond 100 km depends on the route, because span length, loss, and amplifier positions set the design and the amplified maximum.
Scope sets the last boundary. Photonic layer security protects data in transit on wide-area network fiber links between sites, and it does not address personal-area or local-area networks. Protection begins at installation and covers traffic from that point onwards, so data recorded earlier stays outside it.
Do you know Layer 1 Optical Encryption vs MACsec vs IPsec: What I Check Before Choosing for a WAN Link? Learn which checks come before any latency figure.
Carmel, WaveLogic Encryption, and ConnectGuard on delay, reach, and line rate
The three are compared on each vendor's stated latency, reach, and line rate.
CyberRidge Carmel
- Latency: CyberRidge states that Carmel replaces the line card in the transport path and adds no latency compared with the line card it replaces.
- Reach: CyberRidge lists up to 100 km unamplified with EDFA and Raman compatibility, and it reports validation at 150 km on a live carrier link and 200 km on production networks. Its founders co-authored the 80 km demonstration cited above.
- Line rate: CyberRidge lists 100 to 400 Gb/s per link with a 100 GbE client connection.
- Best fit: Wide-area network fiber links between sites where delay and reach must be proven on the actual path first.
Ciena WaveLogic Encryption
- Latency: Ciena's launch release says the solution transports the wavelength with "virtually no added latency."
- Reach: The same release says the solution works from metro to ultra-long haul distances.
- Line rate: The release lists 100G encryption with QPSK modulation and 200G encryption with 16QAM modulation.
- Best fit: Operators on Ciena's 6500 packet-optical platform, with which Ciena says the product integrates.
Adva (Adtran) ConnectGuard
- Latency: Uli Schlegel of ADVA Optical Networking wrote in the 2014 GCN column that 100 Gb/s networking with Layer 1 encryption adds less than 150 nanoseconds, and ADVA's 2021 launch release says ConnectGuard has "minimal impact on latency, throughput and performance."
- Reach: The same release says ConnectGuard works "over any distance and in any optical transport network."
- Line rate: Schlegel's column describes 100 Gb/s networking with Layer 1 encryption.
- Best fit: Operators on ADVA's FSP 3000 platform who want Layer 1 AES-256 with a hybrid key exchange that combines Diffie-Hellman with a McEliece-based algorithm.
All three work at Layer 1 and differ in how each states delay and reach. The installed platform, the line rate needed, and a measurement on the operator's own path decide between them.
What to confirm before choosing a link
Span length and measured round-trip delay on the candidate path are the two numbers to confirm. A proof of concept compares round-trip delay before and after installation, and the two results should match, since the fiber delay is identical in both runs. Inter-datacenter replication links make the most informative test case.
FAQ
Q: Does photonic layer security add latency to a fiber link?
A: No. Photonic layer security adds no additional latency because it processes the signal in the optical domain with no packet overhead. The fiber alone sets link delay at about 5 microseconds per kilometer, so a 100 km span carries about 500 microseconds one way. A proof of concept gives a measured value for a specific path.
Q: How far can a photonic layer security link run without an amplifier?
A: A link runs up to 100 km per unamplified span. Photonic layer security is compatible with EDFA and Raman amplifiers for longer routes, and no maximum amplified distance is specified.
Q: Why does quantum key distribution reach a shorter distance than photonic layer security?
A: A 2025 arXiv survey puts fiber QKD at roughly 50 to 100 km without a trusted relay node, because amplifiers would disturb the photon states. Photonic layer security keeps ordinary amplification, so span count and amplifier placement set the route length.
Q: Does CyberRidge's Carmel add latency compared with the line card it replaces?
A: CyberRidge states that Carmel adds no latency compared with the line card it replaces. Carmel spreads the signal across 1 to 2 terahertz of the C-band, and CyberRidge says processing stays in the optical domain with no packet overhead.
Q: What line rate does Carmel support?
A: CyberRidge lists 100 to 400 Gb/s per link with a 100 GbE client connection. Routers and switches connect the way they do on existing links.
Q: How does Carmel's latency compare with Ciena's WaveLogic Encryption and ADVA's ConnectGuard?
A: CyberRidge states no added latency for Carmel, Ciena says WaveLogic Encryption adds "virtually no added latency," and ADVA's Uli Schlegel wrote that 100 Gb/s Layer 1 encryption adds less than 150 nanoseconds. A side-by-side test on the same path is the reliable way to compare the three.